Note: 309 are Split case & 311 or tunnel
type transmissions
1-- #001 301 227...Seal
order
$1.75
2-- #001 301 209...Bushing order
2-- #001 398 227...Bushing & Seal Kit...1-seal 2-bushings
& holder order
$7.95
3-- #111 301 207...Bush,
Gearshift Housing 3/4" long
order
$2.45
3-- #111 301
207x...Bush, Gearshift Housing 7/16" long
order
$2.45
3a-- #113 301 205G...Nosecone...New...order
$49.95
3a-- #211 301 205H...Gearshift Housing used to install 311 Trans
in place of 309 Trans (use with 211
301 265 T-2 mount) order
3a-- #211 301 211G...Gearshift Housing for early T-2 (shifter
"hockey stick " is approximately 3" below top bolt
hole hole.)
3a-- SBNC...Nosecone...S.B. 3-hole mount
order
recycled $30.75
3a-- #211 301 215...Nosecone Gasket
"Quote"
$1.00
4-- #N 010 290 1...Hex Head Bolt...M7x25
5-- #N 012 234 5...Spring Washer...B7x14x0,8
6-- #113 301 229A...Plug...When Back-up Light
Switch is not used
6-- #211 941 521P...Plug...When Back-up Light
Switch is not used same as above "Quote"
$2.05
6a-- #211 941 521...Back-up Light
Switch "Quote"
$5.98
7-- #N 013 816 5...Sealing Washer for Plug or
Back-up Light Switch
8-- #N 010 353 3...Hex Head Bolt...M8x42
9-- #N122282...Spring Washer...B8x15x0,8
10-- #211 301 215...Nose Cone Gasket "Quote"
$1.00
10-- #001 301 215...Gasket...comes in gasket kit
# 41
11-- #113 301 169F...End Plate Casting
12-- #113 311 599...Plug
13-- #N 011 134 5...Hex Nut...M10
14-- #113 301 177...Adjustable Support for
Reverse Lever
14a-- #V13 301 177...Adjustable Support for
Reverse Lever "Quote" recycled
$3.95
15-- #N 012 242 4...Spring Washer...B10x18
16-- #111 301 115...Plug
17-- #111 971 237A...Ground Strap...Note:
This must be in place when using stock tran. mounts. "Quote"
18-- #N 011 527 11...Washer...A10,5x21x2
19-- #N 012 231 4...Spring Washer...A10x18x0,8
20-- #N 011 010 13...Hex Nut...M10
20-- #VNSM...Special 10mm Hex Nut with 15mm Head Recycled
"Quote" .45cents
each
21-- #N 011 010 11...Hex Nut...M10
22-- #N 012 230 7...Spring Washer...B10x21x1
23-- #N 014 503 4...Stud...AM10Ax42
24-- #111 301 155--Starter Bushing 6-volt
8/59-7/66 "Quote"
$1.95
24-- #113 301 155--Starter Bushing 12-volt 8/66-on "Quote"
$1.75
24-- # V004027--Starter Bushing 6-volt case using 12-volt Starter
"Quote"
$3.95
24-- #PSB126--Starter Bushing 12-v case using 6-volt Starter "Quote"
$3.95
25-- #113 141 181A...Not used on early transmissions using
early T.O. Bearings "Quote"
$3.95
26-- #N 040 203 3...Hex Head Bolt...M7x15...not
used on early S.A. Tranys
27-- #111 300 044QX..Transmission Case
27-- #113 301 051R...Transmission Case
28-- #113 301 141B...Oil Drain Plug w/Magnetic "Quote"
--
#VM00 5773...Tran Drain Plug 17mm Allen w/3/8" drive "Quote"
$5.95
29-- #113 301 191...Gasket...comes in gasket kit
# 41
30-- #113 301 113...Dowel Pin
31-- #111 301 127E...Oil Filler Plug...M24x1,5 "Quote"
-- #VM00
5773...Tran Drain Plug 17mm Allen w/3/8" drive "Quote"
$5.95
32-- #113 301 165C...Bracket for Clutch Cable
32-- #V113165...Bracket for Clutch Cable "Quote" recycled
$6.95
33-- #V113 301 111...Packing..."Quote"
Recycled $4.50 Good as new.
Note:
End play or tension is adjusted by adding and removing gaskets
from behind axle tube flange. The Axle & Tube (without brake
drum & backing plate) should just move from it's weight. If
tight add gaskets & if falls fast, remove gaskets.
see
#3
34-- #8125N...Hex Nut...M8
35-- #N122282...Spring Washer...B8x15x0,8
36-- # N 014 398 7...Stud...AM8Ax27
37-- #N122282...Spring Washer...B8x15x0,8
38-- #N 010 332 4...Hex Head Bolt...M8x32
39-- #113 301 180E...Side Cover
40-- #--------------Gaskets used for set-up on
most S.A. Transmissions
40-- #113 301 185A...Sealing "O"-ring
41-- #111 398 005A...Manual 4-Speed Gasket
Set...order
**--
Motor to Transmission Mounting Bolts #9 & 10 -->
*Click
**-- #VM00 9507...
Bug
to Bug Transmission Mount...4pc Kit w/straps
"Quote"
$26.95
|