1800vw

We will list accurate Part Numbers to the best of our ability but we do not say they are 100% correct.So use them at your own risk. If you find a wrong part number please let us know. Note: VW often made changes in the 8th month so if you have a 1968 made before Aug. it might be the same as a 1967....... Part numbers starting with a "V" are Vic,s part numbers..vw@vwhelp.com.. We will put VW part numbers in place as they are available.
Many Parts are available but not listed yet. Shown in Gray -> order > E-mail for price

1-- #111 501 201A...Axle Shaft, Rear, L/R...49-66... 26 5/8" long "Quote"
1-- #311 501 201D...Axle Shaft, Rear, L/R...67-68... 28 3/8" long "Quote"
1-- #VLSA...Axle S.A. Left side... 26 5/8" long...up to 1966 "Quote" recycled 9# $27.97   approximately 8 lbs each
1-- #VRSA...Axle S.A. Right side...26 5/8" long...up to 1966 "Quote" recycled 9# $37.97
1-- #VLLA...Axle S.A. Left side...28 3/8" long...1966 -1968 "Quote" recycled 9# $27.97
1-- #VRLA...Axle S.A. Right side...28 3/8" long...1966 - 1968 "Quote" recycled 9# $32.97
1-- #111 501 201A --- Axel L or R 1949-66 "Quote"
1-- #311 501 201D --- Axel L or R 1967-68 "Quote"
1a-- #113 517 191...Fulcrum Plate (fits on each side of axle flats)... up to 7/68 order
1a-- #113 517 193...Fulcrum Plate Oversize (fits on each side of axle flats)... up to 7/68 "Quote"
Spade End side clearance (large flats) is .001"/.010" and clearance on rounded end of spade (small ends) is .001"/.004"
Splined end for Brake drum is 30mm / 1.181" diameter   Early "up to 66" have Short Splines 1 7/8"    and     1966 and Later (including IRS) have long splines 2 1/2"

2-- # AXTR...Axle Tube Assy...Rt side for short axle...up to 1966...20 7/8" Long w/bearing casting "Quote"    approximately 10 lbs each
2-- # AXTL...Axle Tube Assy...Left side for short axle...up to 1966...20 7/8" Long w/bearing casting "Quote"
2-- # ATLR...Axle Tube Assy...Rt side for long axle...1966 - 1968...22" Long w/bearing casting "Quote"
2-- # ATLL...Axle Tube Assy...Left side for long axle..1966 - 1968...22" Long w/bearing casting "Quote"
2a-- #V113 301 111...Axel Tube Packing "Not Shown" See # 33 *click here "Quote" recycled $4.50

3--...Gaskets for setting end play included in gasket set #111 398 005A   Note: End play or tension is adjusted by adding and removing gaskets from behind axle tube flange. The Axle & Tube (without brake drum & backing plate) should just move from it's weight. If tight add gaskets & if falls fast, remove gaskets.

4-- # V11 501RF...Axle Tube Retainer Flange "Stock stamped steel" "Quote" recycled $8.95 each

5-- #113 501 159...Large boot clamp "Quote"

6-- #111 501 153B...S.A. Boot...w/clamps... stock black order
6-- #111 598 021A...S.A. Boot Kit... w/clamps...German order
6-- #V009974...S.A. Boot...(set of 2) order $12.95

7-- #111 501 159B...Small boot clamp "Quote" $ .59

8-- #211 501 191..Rubber bumper stop (2 required) 58-79 "Quote"
8-- #VRRB... Rubber Stop Assy. "1-Right or 1-Left" .."Bracket w/rubber stop" "Quote" recycled $5.97 each

9-- #VSWP...Taper Pin   "Quote" recycled $2.00 each

10-- #311 501 169B...Outer Axle Tube bearing casting w/shock mount "Quote" recycled $32.97

11-- #311 598 051...Gasket Kit also includes #14, #16, #19 order
Kit comes wit 2-gaskets but only one used on Bug T-1 behind #21

12-- #VASS..Axle spacer...OD=1.690" / ID=1.185" / .255" thick & inside radius goes in
... "Quote" recycled $3.00

13-- #311 501 283...Bearing "Quote" $11.95

14-- #113 501 291A..."O" ring seal...OD=2 7/8" x .105" order

15-- #............................Spacer (not used)

16-- #111 501 296..."O" ring seal...OD=1.225" x .135" between bearing & Spacer order

17-- #VSAS..............Spacer...OD=1.750" / ID=2.185" / .555" to .610" thick & outside bevel goes out. and the outside diameter must be perfectly smooth for seal to last. "Quote" recycled $5.95

18-- #113 501 315...Seal ( also comes in kit #311 598 051 order ) open side towards trany.

19-- #.............Shim...OD=1.750" / ID=1.180" & .020" thick (in Kit #311 598 051 order

20-- #V1015...Set of 4 bolts (10 x 1.5 x 40mm or 1 1/8" long with small 14mm head) "Quote" recycled set of (4) $3.00

21-- #VRBC...Bearing Cap (Several different ones used - Match depth to old one) order
... Several styles available "We can Match with proper information" "Quote" recycled $8.95

22-- #113 501 615K... 4-lug brake drum 8/67-on 9 1/8" ID & 2.1/2" spline length order
22-- Also See #24 on Brake Drums Note: The drums should slide on and off by hand, Do not force Drums on spline.

22a- #111 601 139... Lug Bolts 12mm stock 5-Lug... "Quote" $1.20 order
22a- #VM009566... Lug Bolts 12mm Chrome "Set of 5"... "Quote" $12.95
22a- #VM009565... Lug Bolts 12mm Long "Set of 5"... "Quote" $12.95
22a- #211 601 139... Lug Bolts 14mm stock 4-Lug... "Quote" $1.50 order
22a- #VM00 9568.... Chrome Lug Bolts 14mm 4-Lug set of (4)... "Quote" $9.95
22a- #VM702810... Lug Bolts "Press in Race Studs & Nuts 14mm" ... order $9.95/set

23-- #111 501 221...Axel nut (non-flanged) use 36mm socket & torque to 245 ft lbs. "Quote" $3.00
23-- #311 501 221...Axel nut (Flanged) use 36mm socket & torque to 245 ft lbs. "Quote" $1.98
........#AC000141...36mm Socket with 1/2" drive *check* "Quote" $7.95   "How to remove frozen Nuts"

24-- #N12 548 1.......Cotter Key 1 1/8" to 2 1/5" long and approximate .190 dia. "Quote" $ .20

25-- #113 501 615D..Brake Drum... 5-Lug. 57 - 7/67 order 9 1/8" ID & Spline length of 1 7/8" "Short"
25-- #311 501 615E...Drum...T-3...5-Lug 8/63-7/65 order 9 13/16" I.D. & Spline length of 2 1/2" "Long"
25-- #181 501 615A...Drum..Thing...5-Lug order 9 1/8" ID & Spline length of 2 1/2" "Long"
25-- Also See #24 on -> Brake Drums
25a- #111 601 139... Lug Bolts 12mm stock 5-Lug... "Quote" $1.20 order
25a- #VM009566... Lug Bolts 12mm Chrome "Set of 5"... "Quote" $12.95
25a- #VM009565... Lug Bolts 12mm Long "Set of 5"... "Quote" $12.95
25a- #211 601 139... Lug Bolts 14mm stock 4-Lug... "Quote" $1.50 order
25a- #VM00 9568.... Chrome Lug Bolts 14mm 4-Lug set of (4)... "Quote" $9.95
22a- #VM702810... Lug Bolts "Press in Race Studs & Nuts 14mm" ... order $9.95/set

26-- #V104015HB... 10x40x1.5mm...Hex bolt but with small head needed for clearance. "Quote" $0.60
"Quote"   10x1.5-22mm with std 17mm head used with single spring plates #102515HB $.45 each

27-- #VTCO...............Spring plate cap "Quote" recycled $6.07
27-- #V511101..........Spring Plate Caps (set of 2 ) Chrome order
27-- #113 511 227A --- Cap w/o hole L or R 1960-69 & 1949-52 "Quote"

28-- #V510001..........Spring Plate Grommet 50-67 outer knobby.. 1 7/8"ID order
28-- ...........................Spring Plate Grommets50-60 inside round..... order

29-- #V510001..........Spring Plate Grommet...inner knobby...1 7/8"ID order
29-- #311 598 245 --- Spring Plate Grommets (set of 4) 1960-68 "Quote"

30-- #VUSP...............Spring Plate "Quote" recycled $35.07
30-- #111 511 205B --- Spring Plate, L or R --- 1960-68 "Quote"
30-- #V4959...Spring Plates for Long Bars 1949-1959 order recycled $69.95
30-- #V268...Spring Plate T2-Bus up to 1968...order recycled $34.95
.. Also see this page --> *Click

31-- #VTBS................Torsion Bar 21 3/4" long 61-68 "Quote" recycled $38.97
31--#V............. Torsion Bar--65-67 Fast Back-- mm--24 11/16" long
31-- #V501 300..........Torsion Bars 26mm x 21 3/4" long order

32-- #VSWT...............Torsion Housing cut from S.A. Pan "Quote"
Note: We recommend always using the IRS torsion housing when building a car then you can use S.A. or IRS transmission.   Convert your old Swing Axle to an IRS torsion. order

33-- #V128015HB...Shock bolt 12x80x1.5mm or 12mm x 3 1/8" long "Quote" $ .98

34-- #113 513 031G...Shock Rear Stock 1/54 - 7/68 order $19.95
34-- #KG5529..............Shock Rear Gas KYB order
34-- #AC513 001B...Shock Rear Coil Over order Note: Most aftermarket rear shocks fit 1950-1977, Stock IRS rear shock has slightly more travel and wider mounting sleeve at bottom of shock for centering.

35-- #V1215N...............Nut for Shock 12mm "Quote" $0.75
35-- #V1215NL............. Nylock 12mm Self locking nut "Quote" $ .80

...Page on Transmission Gears *click

Spring Plate Stops-->*ck --- Swing Axle Transmission Parts Page-->*Click --- Spring Plate Retainers...Chrome-->*ck --- S.A. Tips-->*ck  --- R-Suspension-->*Click   --- IRS Parts-->*Click --- Weld in IRS pivots to convert SA to IRS->*ck

Go Back          <-- Good reason to use Spring Plate Retainers

Victor Comp. Products Inc. **--Vic's--**Phone 816-650-3535 • 230 S Hudson St., Buckner, Missouri, 64016, US
All Questions should be E-Mailed to Vic's

Contact Webmaster