5-- #111 115 487...Gasket, Oil Filler Cap...8/55-7/74
5-- #059 103 487...Gasket, Oil Filler Cap

6-- #113 115 495...Nut, Oil Filler...61-79... Sometimes it helps to heat #1 where nut screws in order to remove Nut. --- Screw in Filler, All in one order $14.95

7-- #113 115 451D...Oil Filler Tube & Cap...66-74
7-- #113115 450...Oil Filler w/down tube but no top breather tube fitting...chrome-> order $9.75

8-- #113 115 475...Gasket, Oil Filler to Stand up to 7/74...Comes in gasket kit...

9-- #113 115 611...Dip Stick 12-1600cc...up to 7/79
9-- #211 115 611A...Dip Stick...

10-- #111 115 491...Grommet

11-- #113 115 6312...Oil Dipstick Tube..."Quote" $5.95

12-- #311 115 541...End Cap, Crankcase breather vent tube (duck-bill)...64-72 "Quote" $1.35
12a-- Diameter of inlet and outlet oil holes in case should match holes in Oil Pump
          Note: If you have a new Mexico case be certain oil passages in case line up with pump holes. 

13-- #111 115 111A...Oil Pump to Engine Gasket...6mm holes
13-- #111 115 111B...Oil Pump to Engine Gasket...8mm holes  thickness not critical like #16 order .30 cents

14-- #-- Not available as separate parts. Replace as an assembly see # 15a
14a-- #311 115 107KHD...Oil pump assembly...6mm...Stock Pump with  long gears. "Quote" 
14a-- #111 115 107AKHD...Oil pump...8mm bolts. Large passage HD/26mm long gears. "Quote" 
14a-- #111 115 107BK...Oil pump assembly...8mm bolts...26mm  gears...72-76  "Quote" 
14a-- #V115 136...Oil pump assembly HD Cast Iron Body with 30 long gears for dished cam. "Quote" 
14a-- #V115 135...Oil pump assembly HD Cast Iron Body with 30 long gears for flat cam. "Quote" 
14a-- #AC115160...Oil pump with attached Filter...up to 71...3-bolt cam gear order $43.95
14a-- #AC115170...Oil pump with attached Filter...71-on...4-bolt cam gear order $43.95
14a-- #113 115 101C...Oil pump assembly for Automatic 8/81-on exchange  "Quote" 

15-- #Gears...Not sold separate ...see #14

16-- #111115 131A...Gasket for Pump Cover 6mm studs 
16-- #111 115 131B...Gasket for Pump Cover 8mm studs (** Import-> .003/.004" thick **) order .30 cents
   ** Check the thickness of this gasket very carefully as you will often find several gaskets stuck together do to the way they are made. ** this sets oil pump end play.

17-- #311 115 141...Cover Plate...6mm holes "Quote"  $4.95
17-- #311 115 141C...Cover Plate...8mm holes order  $5.50
17-- #VM00 9148...Bug to Bus Rear Mount...Any T-1 Motor in 68-71 Bus order
17-- #VM00 9226...Cover Plate with outlets...8mm holes...Alum  order

18-- #111 115 161...Oil Pump nuts... Sealing 8mm  order (4) $1.80
18-- #111 115 159...Oil Pump nuts... Sealing 6mm  order (4) $1.20

19-- #11-- #........Oil Plug   order
19-- # VORP...Recycled  order $2.35
19-- #VM00 9198...Adjustable Oil Pressure kit  order  "Quote" $7.95

20-- #...Washer comes in gasket kit & Oil change Kit  order .60 cents for complete Kit

21-- #------------...Spring "short" next to flywheel  order   Note: Long Spring is used at rear of car Not as shown in photo   Note: T-1 Dual Oil Relief cases started 8-70
21-- #AC37 0100...Spring Kit H.D. Single Spring comes with heaver springs & late style pistons order   Single Long Spring at rear of car "new stock" = .928" or 23.6mm free length
21-- #AC10 0120...Spring Kit H.D. Dual Spring comes with heaver springs & late style pistons order  Short spring with shortest piston  " no grove on outside diameter of piston"
21-- #V105389...Adjustable Pressure spring kit. (oil pressure can be adjusted with allen wrench without removing plug ) "Quote"

22-- #...Comes in kit...longer of 2 pistons...closed end up  see #21

23-- #N 14 396 1...8mm Oil Pump Studs..8 x 50mm(1.969")...(4). "Quote" 
23-- # 6mm Oil Pump Studs...6 x __...(4)...

24-- #...Comes in kit...longer of 2 pistons...closed end up  see #21    Note: T-1 Dual Oil Relief cases started 8-70  
 "No grove on outer diameter of piston up to 8/70"   Grooved piston can be used as replacement on all motors

25-- #...Spring "Long" at rear of car  order   Note: Short Spring is used at front of car Not as shown in photo See #21

26-- #...Washer comes in gasket kit & Oil change Kit  order .60 cents for complete Kit

27-- #11-- #........Oil Plug   order
27-- # VORP...Recycled  order $2.35
27-- #VM00 9198...Adjustable Oil Pressure kit  order  "Quote" $7.95

28-- # ...Comes in Oil Change Kit...      order .60 cents for complete Kit

29-- #N110624...6mm Oil Cap Nuts  (requires 6)  order (6) $1.80 .30 cents each        Step studs 6 to 8 & 8 to 10mm --- order

30-- #113 115 193...Plug "Oil Drain" order $1.35
30-- #VM005110...Plug Oil drain with magnet. order $2.99
 . . . Prevents metal from traveling around your engine in the oil. Clean it thoroughly every time you change the oil. . . .

31-- #...Washer comes in gasket kit & Oil change Kit  order .60 cents for complete Kit

32-- #113 115 181A...Oil Plate ( late model without drain hole ) order $2.95
32-- #113 115 181A...Oil plate ( early with drain plug hole for # 7 ) 
32-- # VM008911...Oil plate "Chrome" ( early with drain plug hole for # 7 order $5.95
After years of use & over-tightening the hold down nuts the oil plate is no longer flat. The area around the 6 holes becomes concave. This can be easily fixed by placing a ball bearing. or the round end of a bullpen hammer over each hole a taping with a hammer. 
33-- #113 115 189A...Oil Strainer Gasket (requires 2) order .60 cents for complete Kit
33-- #113 198 031...Oil Change Kit (includes 2- #1, 6- #4 and 1- #6) order  .60 cents for complete Kit

34-- #111 115 175A...Oil Sump Strainer 36hp/1200cc 54-60 "Quote" 
34-- #311 115 175...Oil Sump Strainer 40hp/1200cc 61-65 order $3.95 
34-- #113 115 175...Oil Sump Strainer 12-1500cc...8/60-7/67
34-- #311 115 175A...Oil Sump Strainer Small Hole...15/1600cc 8/67-7/69 order $3.95
34-- #111 115 175B...Oil Sump Strainer Large Hole...15/1600cc 8/69-7/79 order $3.95

35-- #113 115 189A...Oil Strainer Gasket (requires 2) order .60 cents for complete Kit
35-- #113 198 031...Oil Change Kit (includes 2- #1, 6- #4 and 1- #6) order .60 cents for complete Kit

36-- # Location of oil sender...on rear or on side...If no threaded hole, then case is T-3 and sender is located on oil cooler.

      VDO Oil Pressure Gage 0-80 psi --> "Quote"  $32.95             VDO Oil Pressure Dual Sender --> "Quote"  $32.95